#diy #squeaky-floors #hardwood-floors
00:00 – Intro
00:12 – Squeak no more kit
00:55 – Locate the squeak
01:16 – Find the joists
02:17 – Drive the screws in
04:25 – Fill in the holes
06:47 – Results
Squeeeeek No More Kits
https://amzn.to/3PonhKT
https://amzn.to/3G6bWLi
Minwax wood putty
https://amzn.to/455MsYw
——-
As an Amazon Associate I earn from qualifying purchases.
source
Still hear it…
Great tip on how to find the joist spacing. Thanks!
Watch out for pipes and electrics.
We moved int an old house (100+) and all the floors were carpeted wall to wall. We found beautiful hardwood below and had them refinished. While pulling up the old carpet, held down by THOUSANDS of staples it created a ton of squeakers. This works well but its still a work in progress
7:15. When my wife would say, "not good enough."
Whispering while you have drill effects at 10 wtf your waking up my wife!
How mad do you think my landlord would be if I did this in my apartment
What if you don't have joists? Mine is on a concrete sub floor covered with 100mm insulation.
Don’t use an impact driver. The screw can snap before it’s in all the way. Don’t pulse the drill. Same problem. Just drive it in at full speed.
My boards run parallel to the floor joists leaving most over just the subflooring which are 1x's and they are too soft to hold those scews in tight enough. The diagram (1:18) shows the same scenario which is 90 degrees opposite of what the video demonstrates. https://youtu.be/ooFOKTpDfyc?si=6rbBmHSQ8XS5MlT0&t=77
¿..!
There's my underfloor heating fucked. Wtf you drilling that deep for
liquid nails for wood flooring not actual nails as some will squeak
In civilzed countries people have concrete foundation underneath their floorboards.
I would rather have a sqeeky floor than a gas explosion. Diyer's please don't be tempted to do this. You can not tell if there are pipes or cables under that floor
If you have a basement or crawl space, have someone stand on the squeaky spot and bounce up and down, then insert a thin shim in the gap and tap it in. That stops the squeak without having to drill through the topside of the floor.
So you rely on the threads of headless screws to keep the floor secured to studs. No risk of test drilling through pipes, electrical wires etc?
if you are annoyed with that squeak, you must be hard to live with…
and now I see in the comment section where the humanity is going…
Well done with the video!
and for my next trick I will show you how to mount floating shelves in your entry hall by directly drilling into the drain line from the upstairs bathroom. you'll never be able to flush the toilet again but those shelves won't move at all!
Just sell the house, problem solved.
what about pipes, a lot of squeaky floors are where pipe runs are.
For God's sake, don't blindly drill holes in the floor. There are water and gas pipes under there.
Of course, you will never hit a water or gas pipe, nor an electric cable !!
Or just use a finish screw ,,
relieving.
This is temporary fix, and a complete waste of money.
Here's a tip that "may" work for some people. Try to locate the exact location of the squeak as shown in the video and then lay a small piece of 2 by 4 (about 6 inches long) over top of that spot. Wear ear protection and using a heavy hammer, hit the 2 by 4 a few times really hard. Keep checking to see if the squeak is gone. The noise is usually caused by a nail that has moved due to settlement in the house. We got lucky and got rid of 2 really bad squeaks in our kitchen, which has a 1-piece vinyl floor.
Unfortunately, often times the sqeeky area is no where near a joist.
If you drill the hole in the grain of the wood you can hide it better with wood fill. Another tip. Use a flat head screw driver to make the round hole a rectangle shape. It looks more like wood grain.
Never do this in the U.K. I guarantee it will lead to disaster. There’s likely to be a water pipe or pipes under here or possibly a cable. You have to remove the floor to find out. You may even have under floor water heating.