Visit our website at http://www.mydiygenius.com.
Need to replace one of your Click-Lock Planks? There’s no need to worry – replacing a plank is a quick and simple process. Follow the instructions in the video to replace your Click-Lock plank in just minutes!
To view other Allure Flooring videos, visit our channel: https://www.youtube.com/channel/UCaZIP_mXUw9g3aGeifeTBKw
source
Why is he cutting off edges of new plank?
What adhisive did you use??
But how stable is this? Is this something you'll be regluing every few years?
If your vinyl is older than 5 years do not attempt this it will just shatter if your floors f*** up just replace it
Shoutout for the clear steps! I always tell clients to keep the subfloor flat within 3/16" over 10 feet for click-lock floors—this prevents locking failure down the road. Solid demo!
What if you have to remove that one in a couple years won't be easy after you glued it.
Awesome video. I have the same issue and have NOT A CLUE how I'm going to do this. When you cut the diagonals out, did you score first with your saw or simply use a very new blade and cut if by hand using your box cutter knife?
CA glue is too brittle, this repair will fail. Lexel and weights on top for 48 hours is the way.
So basically you re glueing down the replacement, not acttually using its factory "Clik Lock" tongue and groove system? My LVP had to be installed clicking together at angles, not the lay down and beat in..
i feel like engineered wood or just hardwood floors are better in this case. sigh, just going to have to live with several scuffs and dents on my floors.
Cyano glue should be used on one face only, it will not cure if applied to both surfaces as instructed here.
Also the video is proof that glue was only applied to the floor planks because had he applied glue all around the new plank as claimed holding it in a flat grip with his ungloved hand as he did would have necessitated a trip to hospital.
Children, do not blindly follow what muppets on the internet tell you to do!
This is an old video, but maybe this comment will save you. Remember that IF YOU USE SUPERGLUE, then DO NOT USE ACETONE to clean up, because ACETONE dissolves superglue.
This didn’t work for me and I’m really sad ðŸ˜
You don’t need a square or a saw to cut and remove the damaged plank unless you’re a total moron.
This only works with this product, which looks flimsy enough to bend. If you have a heavy duty (life proof xl), or another product with two locking edges it won't. Plan on taking the time, and pulling trim and boards to get to the damaged one. No way you are pulling this out, then popping another one in (especially with super glue). Do it right, take the time, stack your boards in the rows they came out in, but you're pulling rows to get to the damaged one. It is what it is. You're welcome. Side note: the 45 triangle method for removing is legit, but you better practice sliding these in between pieces, and running from both sides of the wall to dial this in. Again, you're welcome.
Glad I looked..guy who put floor in said nope have to replace whole floor..I was like, ahh I don't think so😅
Thank you. Straight to the point
Works perfect thank u
This looks simple enough, but I talked to a flooring guy and he said that it’s not this simple. It’s actually kind of hard to do and he’s charging $100 per plank. And this is the second guy that I’ve talked to that says it’s hard to do and I have the replacement planks. It would be labor only basically for them to do it
was about to rip up my whole room
If the flooring connected with the baseboard what should I do?
What kind of adhesive plz?
That replacement plank is way not matching.
Can this work for a manufactured home??
Doesn't work!
So I just trim that corner off on the sides that click in?
difficult bits conveniently left out, be wary of this horse s folks, job is much harder than this.
Definitely have acetone ready to clean because that glue is no joke
Not sure why the handyman or contractor videos are so long when this guy did it in 2 min.
Does it peel over time and separate from the edges, or does it stay like the original?
Why did you skip removing the second triangle??
We installed Coretec Enhanced Click Lock couple years ago. Now a carpeted area next to it needs replaced and we are thinking about extending the Coretec Plus Unhanced (click together) into the attached room area. The issue is, the area we want to add it to is at the END of all older planks that are basically laid in a way that they are pointing at the new room. Please tell me there is a way to add on without ripping out too much of the old. I wondered if where the last ones left off with shorter planks before the trim edge between that and carpet start, that those short peices could carefully be slid out and new longer boards slid in those spots to continue the floor? If not what would this look like? I wont tear up the whole old floor to do this, but that end pieces I am fine with. I don't want to compromise the click lock edges either on the old pieces. I would love your feedback on this. Thank you for your time! Great Video!
What is a cyanocrylate? Is that anything like Elmer's glue?
Best
nice
I did not have a good long term result following this video. It looked great for a few months and then a long edge lifted up about a millimeter and there is a noticeable gap now. Should've just left it alone 😔
Not sure what edges I cut off on new plank??
I would actually comment but Youtubes new AI automatically deletes 99% of what I post or write.