Not all sagging floors are the same, and the fix depends on the cause. This video covers the three most common repair approaches: sistering a damaged joist, adding mid-span blocking to stop bounce, and using a hydraulic jack with a temporary steel column to lift a settled beam — plus how to tell which one your floor actually needs.
📋 Free Home Maintenance Checklist → https://the-struggle-bus.beehiiv.com
PRODUCTS USED & RECOMMENDED:
→ Acrow Adjustable Steel Building Column / Lally Column: https://amzn.to/4d7tMBf
→ 20-Ton Hydraulic Floor Jack: https://amzn.to/4u3VCSx
→ Simpson Strong-Tie Joist Hanger LUS26 (10-Pack): https://amzn.to/4tXG4zx
→ Structural Screws 3/8″ x 4″ (50-Pack): https://amzn.to/4waFa4e
→ Post Level (Magnetic): https://amzn.to/4dkihCR
PRO TIP: Before you lift anything, find out why the floor sagged — joist rot, settling foundation, over-spanned joist, or removed load-bearing wall. Jacking a floor without fixing the root cause just means it sags again. A $300 structural inspection is cheap compared to doing the repair twice.
Subscribe for structural and foundation DIY tips: https://www.youtube.com/@Housebarons
As an Amazon Associate I earn from qualifying purchases.
#SaggingFloor #FloorRepair #JoistRepair #StructuralRepair #HomeFoundation
source
📋 Free Home Maintenance Checklist → https://the-struggle-bus.beehiiv.com — essential repairs every homeowner should know. 🔧
What is wrong with shimming it. I do so for decades and passed inspections many time and nobody called me back to fix it every. Write in search box "Zell carpentry leveling of floor with furring stirps".
i bet alot of flippers are taking this guys advice and in 3 months it turns into the new owners problem.
none of these seem like legitimate fixes. jacking up the floors and addressing the fact that the beam is compromised seems like the only reasonable fix. none of these solutions address the structural issue of the beam failure.
No one who watches a how-to video is going to ever hire a structural engineer, but at least you can say I told you so if they drop a house on themselves.
First thing you need to do is forget everything this guy said. No one does this crap unless you're this guy
Option 4, scabbing. Similar to sistering but not full length.
I like this guy. He’s more reasonable than going full nuclear.
Wtf? Why not jack up the first 2 or 3 joist with a 4×4 or 4 inch I beam and it will prob be good for another 100 years?
I do leveling with furring strips. "Zell leveling of floor".
My situation is that as you say that over time the house will settle down, and I think that if you just put shimmies under or over the subfloor that is not going to resolve the issue as good as either replacing the joists or sistering it. Am I right ?
This was very helpful information. What caused the sag. I think my problem is carpenter ants. So joists will have to be replaced. What a mess.
This is terrible advice. The structural issue should be addressed… I am shocked that was not even mentioned.
It seems to me that you're only pushing the trash under the rug, not actually fixing the issue.
My house was built 70 years ago out if oak. The kitchen had a peninsula until i bought it. That weight caused a sag. I removed the peninsula but i can see the dip where it was.
Can I go under the house and jack up the studs that sagged and add something to support them? In this case I’d think you wouldn’t have to bother with the subfloor or finished floor as all the work would be done underneath.
🙄 3 options…none of which are post jacks to raise the joists themselves?
If you've determined that the floor sagging was caused by your foundation sagging, do not do option 3.
Option 4: mark level line in different spots along the wall near the sagging floor – screw on temporary wood blocks where the bottoms on the blocks are flush with the level marks – take up your old finished flooring – start fastening on luan (¼in or 3/16in plywood) underlayment to the already level section of your floor, but do not FASTEN the luan to the sagging areas. Position the edges of these luan sheets UNDER the temporary blocks- drill 1/4in holes through the luan (don't go through the subfloor) that is along the most sagged down areas – drill some screws slightly into the luan (not into the subfloor) near the drilled holes just so that you can grab the screw heads and slightly lift up on the luan. – while slightly lifting the luan near the drilled holes, place the nozzle from a sprayable foam gap filler and spray in the foam in every hole from different angles around the hole, and under the luan. The foam will expand and raise the unfastened luan up to the undersides of the temporary blocks making them level.
If the floor covering is old and near replacement why not just pull up the carpet or linoleum then look at the pad?
If floor joists need replacing would it be easier to just remove plywood and sub floor all together for a localized area versus sistering underneath. Seems like if you rebuilt the floor completely in damage areas it fixes the problem if you can eliminate the cause. Why put on a temporary bandaid when you can rebuild the supports?
And thats exactly how NOT to fix your floors.
how about go under the house and add lift them all up?!
Thank you😊