How to Patch Strip Flooring | This Old House



This Old House general contractor Tom Silva shows how to repair a hardwood-strip floor. (See below for a shopping list and tools.)

SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse

Shopping List for How to Patch Strip Flooring:
– Carpenter’s glue
– Spray can of high-gloss urethane
– Blue painter’s tape, used to protect baseboard from spray urethane
– Wet/dry vacuum, for cleaning floor

Tools for How to Patch Strip Flooring:
– Utility knife
– Hammer
– Chisel
– Drill/driver, with 5/8-inch spade bit
– Block plane, used to plane width of new floorboard
– Random-orbit sander, with 320-grit sanding disc

Steps:
1 Score cut line on damaged floorboard using a utility knife.
2 Drill series of 5/8-inch-diameter holes down center of damaged floorboard.
3 Use chisel to cut through floorboard along the scored line.
4 Chisel out center section of floorboard between the holes.
5 Use hammer and chisel to knock out remainder of damaged floorboard.
6 Chisel off the lower lip of grooved edge from replacement floorboard.
7 Plane down the width of replacement floorboard, if necessary, to fit space.
8 Apply carpenter’s glue to top of tongue on adjacent floorboard.
9 Set replacement floorboard in place and tap down with scrap block and hammer.
10 Sand repaired area with random-orbit sander.
11 Protect baseboard with blue painter’s tape.
12 Apply minimum four coats of urethane finish to replacement floorboard, allowing each coat to dry before applying the next.

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we’re ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O’Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.

Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
http://bit.ly/AskTOHIG
Tumblr: http://bit.ly/ThisOldHouseTumblr

For more on This Old House and Ask This Old House, visit us at: http://bit.ly/ThisOldHouseWebsite

How to Patch Strip Flooring | This Old House
https://www.youtube.com/user/thisoldhouse/

source

48 thoughts on “How to Patch Strip Flooring | This Old House”

  1. He did this wrong. You take your new piece of wood sand it until it fits then stain it to the right color then spray it with clear and give it a day to dry. Now glue it in place and place something heavy on top of it and give it a day to dry. You do not sand your old floor unless your going to sand the whole thing plus the color of the new board was way off and this spot will never get better.

  2. That spray job probably looked terrible. There's NO WAY there isn't an ugly blob seen from certain angles. Should have just brushed something on only the replaced board.

  3. You have showed me more than anyone else has. I have two metal air intakes that used to go to a heater in the basement that I want removed and no one seems interested to do the job. I have plenty of original wood for repair. My house was built in 1930. Thanks for the video.

  4. I really appreciate the step-by-step approach you took for this flooring repair. It’s great to see how you managed to patch the damaged area without replacing the whole section. I’d love to know more about the best types of finishes for hardwood floors. Have you tried any eco-friendly options?

  5. I made use of his chiseling method and it worked great. The only concern i have with his video is that he does not add enough length to his measurement to penetrate the wall 1/4" which is what the other boards do

Leave a Comment

Your email address will not be published. Required fields are marked *

Shopping Cart