This emergency plumbing guide will show you how to fix a pipe leak under a concrete floor the easy way! If you’ve got a leak under a concrete floor, then this guide is for you! With easy step-by-step instructions, this guide will show you how to fix a leak under a floor in no time using slip couplers. You’ll learn how to fix it and how to prevent future leaks.
Tools i recommend for this job below:
⚪Torch – https://amzn.to/3QViwZj
⚪Pipe Deburrer – https://amzn.to/3wioMBe
⚪Wire Wool – https://amzn.to/3Y2bzID
⚪Slip Coupling – https://amzn.to/3wdNbI5
⚪Radiator Bleed Key – https://amzn.to/3EB1b27
⚪Pipe Cutter – https://amzn.to/3WjTep2
⚪Flux – https://amzn.to/3WkDh1X
⚪Adjustable Spanner – https://amzn.to/3TgI4A8
🛒 My Shop -https://www.amazon.co.uk/shop/thediyguy
► BECOME A MEMBER OF THE DIY CLUB Click! 👇🏼
https://www.youtube.com/c/TheDIYGuy1/Join
► Get FULL access to the Discord Group and other perks!
Follow me on Instagram 👉 the_diy_guy_youtube
Thanks for watching The DIY Guy. My mission is to bring you the best Tips, Tutorials and Tools to help you learn and save money.
Please be advised that this is only a guide which is intended for informational, educational and entertainment purposes and The DIY Guy cannot accept responsibility for any work undertaken. Be safe and have fun! The Amazon links above are affiliate links and as an Amazon Associate I earn from qualifying purchases. I may earn a small commission if you purchase via the recommended links, however this will not cost you any extra.
source
Hope you guys enjoy watching me tackle this awkward little job! Oh and it wasn't me that dug the floor up otherwise I would have given myself a bit more room to work 🤪
not for the American house
Id also advise, if there are more than one pipe as here, to mark the pipes before cutting to ensure you connect the pipes back correctly. 😅
What are you using to dig up the concrete though? A jack hammer?!
Great video. How did you locate the leak to that particular spot?
An electric reciprocating saw would have done that I think.
What did you fill the hole in the floor with?
i couldnt be faffing about with hacksaw blades, multi tool very useful, be helpful if you showed the floor break up as this is a hard point, but good job sir
First pipe had a kink further up that should have been replaced also. Not a plumber but may give problems in future?
Dremel would be ideal in that situation 😊 if you use a Yorkshire jointing piece is that called a Yorkshire tea? Sorry 😢😂
How did the cut out the concrete without making more damage to the pipes?
How did you break up the concrete please?
You can also buy a handle for hacksaw blades
Use a Dremel to cut a pipe like that
What about filling it back in with cement? I believe you should avoid cement having direct contact with the copper. Is this correct?
Couldn't you have connected all the pipes first and soldered them in one go?
good video but can someone say 'advert' every 30 seconds… have you got ads set on 'frequent' and 'many'
I faced a similar issue many years ago and I know how awkward it can be and how difficult it was to solder with wet pipes but we got it done.
how do you get to the leak without guessing, trial and error
How did you repair the hole in the floor? Did you wrap the pipes first?
any tips on finding leak
Cleaning the pipe before you cut it makes it much easier
Excuse the dumb question, but how did you find where the leak was? I have a 3 rooms with concrete floors and there is a leak in the C/H and I need to find the leak, then dig out to expose the pipework. Thank you for all your videos, it's so helpful.
Hi. I am struggling to understand how you managed to drain the copper pipes of water that are below the concrete floor surface given that the central heating drain point is above the concrete floor surface. Can you (or someone else in this community) explain how this is done please?
Are copper pipes supposed to be buried
Into concrete in the floor?.
I guess you are not familiar with an oscillating tool to cut those?
I've got some adhesive tiles coming away from my concrete floor, and it's wet underneath, I think this is going to be my next job so glad I found this vid, great stuff! After having my gravity fed system replaced with a combi, I'm finding a few joints weeping, is this normal because the added pressure from combi or bad soldering in the first place? I think once I mend this, another one will make itself known, this could turn into an endless job! 😒
I had a massive problem yesterday as i was drilling pilot holes in the floor for a carpet trim didn't even go that deep and hit a water pipe. The water and gas pipe are right next to eachother and i found out the hard way that they are so close to the surface of the floor and not buried deeper. Builders cutting corners…
Emergency plumber came out and he drilled through the gas pipe 😮
how did you know where the pipes were ? What caused you to know that the underground pipe was leaking ? Was the floor suspended with floor boards and screed ? I am facing the same issue and have no idea if it is a concrete floor or suspended floor with screed, some guidance will be much appreciated. Thanks
Great info however, you didn't show the application of the soldering?????? You just fast forwarded through the most important part what gives mate?
Enjoyed the guidance but as these pipes were under concrete I would be interested to know how you found the leak under the concrete. Often a leak can show up many meters away from the location of the burst pipe.
What would the concrete mix be to back fill the hole? Also, should it be sharp sand or builders sand
wait how to close the hole on the floor? That is not DIY?
THANKS VERY NICE VIDEO
Could you use plastic hep pipe and fittings instead of copper
Wow i wouldnt mind having you on top of me…sexy little stud arent you? ❤
How did you noticed the leak ?
Tight joints are are nightmare I agree! To cut pipes in this situation I use a multi tool which cuts copper easily. I'm also a wire wool user but I notice that you didn't clean the fittings. If they have been in the box for some time they do need a clean. Also with Yorkshire I put a dab of solder on the joint as belt and braces!!
It's my understanding that it's against plumbing code to have solder joints underneath a concrete slab. Is that not the case here for some reason?
Why not try to bypass the old copper and move to above ground and use pex
Well explained video for the novice.
A tip I was taught by an old plumber was after draining down drill a small hole in the section of the pipe you’ll be cutting out after undoing a large jubilee clip and refitting it on the pipe you’ve drilled. If you have drained the wrong pipe and it’s still full of water you can get a pencil rubber and clamp it over the hole with the jubilee clip to stop the water flooding the place until get to drain the right pipe. Sounds like a bodge but will save you flooding place.
I would like to see how you repaired that section of floor