How to Repair a Sagging Floor | 3 ways to fix a low spot or a sag in a floor



Not all sagging floors are the same, and the fix depends on the cause. This video covers the three most common repair approaches: sistering a damaged joist, adding mid-span blocking to stop bounce, and using a hydraulic jack with a temporary steel column to lift a settled beam — plus how to tell which one your floor actually needs.

📋 Free Home Maintenance Checklist → https://the-struggle-bus.beehiiv.com

PRODUCTS USED & RECOMMENDED:
→ Acrow Adjustable Steel Building Column / Lally Column: https://amzn.to/4d7tMBf
→ 20-Ton Hydraulic Floor Jack: https://amzn.to/4u3VCSx
→ Simpson Strong-Tie Joist Hanger LUS26 (10-Pack): https://amzn.to/4tXG4zx
→ Structural Screws 3/8″ x 4″ (50-Pack): https://amzn.to/4waFa4e
→ Post Level (Magnetic): https://amzn.to/4dkihCR

PRO TIP: Before you lift anything, find out why the floor sagged — joist rot, settling foundation, over-spanned joist, or removed load-bearing wall. Jacking a floor without fixing the root cause just means it sags again. A $300 structural inspection is cheap compared to doing the repair twice.

Subscribe for structural and foundation DIY tips: https://www.youtube.com/@Housebarons

As an Amazon Associate I earn from qualifying purchases.

#SaggingFloor #FloorRepair #JoistRepair #StructuralRepair #HomeFoundation

source

23 thoughts on “How to Repair a Sagging Floor | 3 ways to fix a low spot or a sag in a floor”

  1. What is wrong with shimming it. I do so for decades and passed inspections many time and nobody called me back to fix it every. Write in search box "Zell carpentry leveling of floor with furring stirps".

  2. none of these seem like legitimate fixes. jacking up the floors and addressing the fact that the beam is compromised seems like the only reasonable fix. none of these solutions address the structural issue of the beam failure.

  3. My situation is that as you say that over time the house will settle down, and I think that if you just put shimmies under or over the subfloor that is not going to resolve the issue as good as either replacing the joists or sistering it. Am I right ?

  4. Can I go under the house and jack up the studs that sagged and add something to support them? In this case I’d think you wouldn’t have to bother with the subfloor or finished floor as all the work would be done underneath.

  5. Option 4: mark level line in different spots along the wall near the sagging floor – screw on temporary wood blocks where the bottoms on the blocks are flush with the level marks – take up your old finished flooring – start fastening on luan (¼in or 3/16in plywood) underlayment to the already level section of your floor, but do not FASTEN the luan to the sagging areas. Position the edges of these luan sheets UNDER the temporary blocks- drill 1/4in holes through the luan (don't go through the subfloor) that is along the most sagged down areas – drill some screws slightly into the luan (not into the subfloor) near the drilled holes just so that you can grab the screw heads and slightly lift up on the luan. – while slightly lifting the luan near the drilled holes, place the nozzle from a sprayable foam gap filler and spray in the foam in every hole from different angles around the hole, and under the luan. The foam will expand and raise the unfastened luan up to the undersides of the temporary blocks making them level.

  6. If the floor covering is old and near replacement why not just pull up the carpet or linoleum then look at the pad?
    If floor joists need replacing would it be easier to just remove plywood and sub floor all together for a localized area versus sistering underneath. Seems like if you rebuilt the floor completely in damage areas it fixes the problem if you can eliminate the cause. Why put on a temporary bandaid when you can rebuild the supports?

Leave a Comment

Your email address will not be published. Required fields are marked *

Shopping Cart